News

FKM vs EPDM O-Rings: Which to Choose for Hot Steam Service | DEF SEALS

2026-10-09


When selecting elastomer seals for steam and hot water applications, engineers often hesitate between FKM and EPDM. Even high-fluorine FKM with excellent oil resistance performs poorly under continuous high-temperature saturated steam, which may lead to hydrolysis, hardening and seal failure.

Choosing the wrong sealing material can cause unexpected leakage, costly equipment downtime and frequent part replacement. This guide compares EPDM and FKM (including high fluorine grade) on steam resistance, chemical compatibility, temperature range and suitable working scenarios, helping you pick the right O-ring material for your pump or industrial equipment.

 

What is EPDM Rubber?

EPDM (Ethylene Propylene Diene Monomer) is a synthetic rubber widely recognised as the top elastomer choice for hot water and saturated steam conditions.

EPDM features outstanding resistance to hot steam and hot water. It can withstand continuous exposure to saturated steam up to 150°C without obvious loss of elasticity. Its molecular structure is stable against hydrolysis, so it will not crack or harden quickly under long-term steam service.

However, EPDM has clear limitations. It swells severely when contacting mineral oil, hydrocarbon fuels and most non-polar solvents. If your working medium mixes steam with oil, standard EPDM O-rings are not suitable.

Core advantages of EPDM for steam:

  • Excellent hydrolysis stability
  • Long service life in continuous saturated steam
  • Cost-effective for pure steam / hot water systems

Weaknesses:

  • Poor resistance to oil, gasoline and aromatic solvents
  • Not recommended for oil-steam mixed media
     

What is High-Fluorine FKM?

High-fluorine FKM is a premium fluorocarbon rubber with roughly 70% fluorine content, higher than standard 66% FKM. It is famous for superb resistance to fuel, mineral oil and aromatic hydrocarbons.

Many buyers mistakenly assume that high fluorine FKM works well for steam. In fact, even high-fluorine FKM suffers from hydrolysis when exposed to continuous hot steam. At temperatures above 120°C, the material will gradually break down, lose flexibility, turn brittle and crack.

Peroxide-cured high fluorine FKM has slightly better steam stability than bisphenol-cured grades, but it still cannot sustain long-term saturated steam exposure. It can only be used for short, intermittent steam contact.

Core advantages of high-fluorine FKM:

  • Superior resistance to fuel, hydraulic oil and aromatic solvents
  • Good high-temperature performance in oil medium
  • Low gas permeability

Weaknesses:

  • Poor long-term resistance to hot saturated steam
  • Hydrolysis happens under continuous high-temp steam
  • Higher price than EPDM

Side-by-Side Comparison Table

PropertyEPDMHigh-Fluorine FKM
Continuous saturated steamUp to 150°C<120°C only, short-time use
Oil / hydrocarbon resistancePoorExcellent
Hydrolysis stabilityVery goodPoor
Main applicationPure steam, hot waterFuel, oil & aromatic media
Price levelMediumHigh

Recommended Working Conditions

Choose EPDM when:

✅ Medium is pure hot water or saturated steam, no oil contamination 

✅ Working temperature ≤150°C 

✅ Applications: steam valves, hot water pumps, heating systems

Choose high-fluorine FKM when:

✅ Medium is oil, fuel or aromatic solvent with occasional short steam spikes 

✅ No continuous saturated steam exposure 

✅ Applications: fuel pumps, hydraulic equipment, chemical pipelines with hydrocarbon fluids

 

What if you have both oil and steam?

If your system contains both oil and continuous hot steam, neither standard EPDM nor regular FKM is ideal. AFLAS (FEPM) is a better alternative, balancing oil resistance and steam tolerance, though it comes at a higher cost.

 

Final Summary

For pure hot steam service, EPDM is the preferred O-ring material. Do not select high-fluorine FKM for continuous saturated steam, as hydrolysis will shorten seal life and cause unexpected leakage.

If your system has oil plus intermittent steam, high-fluorine FKM can be considered for short-cycle working conditions.

 

If you need custom-sized EPDM or high fluorine FKM O-rings for your pump or industrial equipment, please share your working parameters: medium, temperature, pressure, groove dimensions and quantity.

DEF SEALS supplies custom PTFE and rubber seals, including EPDM seals and high fluorine FKM O-rings for industrial sealing projects.

 

Suggested links:

Dispensing Valve Seals For Automotive Electronics Potting | DEF Seals
https://en.defseals.com/news_detail_2/70.html
https://en.defseals.com/news_detail_2/71.html
https://en.defseals.com/news_detail_2/82.html



News